Torque Conversion Calculator | Tohnichi America (2024)

FAQs

What is the formula for torque conversion? ›

Torque (T) is shown as the product of the force (F) and the length (L). = 2F x L/2 (If the force is doubled, halving the length will develop the same torque.) = F/2 x 2L (If the force is halved, doubling the length will develop the same torque.)

In inch units, torque is usually measured as Lb-Ft (pounds feet) or Lb-In (pounds inch). The Torque Converter Calculator will allow you to convert Nm to Lb-Ft or Lb-In or vice-versa. The calculator uses the conversion 1 Lb-Ft = 1.35582 Nm.

The equation, Force = Torque ÷ [Length × sin (Angle)], converts torque into force. In the equation, Angle is the angle at which the force acts on the lever arm, where 90 degrees signifies direct application.

Torque in general is given with the symbol (the Greek lowercase letter “t”). The ​​SI-derived unit for torque (moment of force) is N ⋅ m (Newton meters). In the USA, torque is often expressed in foot pounds ( f t / l b s ). To convert N ⋅ m to f t / l b s , simply divide the N ⋅ m value by 1.356.

T(torque) = F(force) * s(distance from pivot) * sin(theta), where theta is the angle between the force and the position vector.

The Mountz torque calculator allows you to convert torque measurement from one type of unit measurement to another. Torque is twisting force that tends to cause rotation. We measure torque by multiplying two factors—amount of force applied and distance from the point of application.

In the US, torque is most commonly referred to as the foot-pound (denoted as either lb-ft or ft-lb) and the inch-pound (denoted as in-lb).

How to convert ft-lbs to Nm? If you're trying the opposite torque units conversion, don't worry: it's equally simple! This time, all you need to know is that 1 ft-lb is equivalent to 1.3558 Nm. This means that to convert from foot-pounds to newton-meters, you need to multiply the value you have by the factor of 1.3558.

torque in American English

1. a twisted metal collar or necklace worn by ancient Teutons, Gauls, Britons, etc.

The equation to calculate horsepower is simple: Horsepower = Torque x RPM / 5,252. You can use our horsepower calculator below to try it out yourself. When it comes to understanding how a dynamometer measures torque and calculates power, it will help to know a few more basic definitions and formulas.

What is the general formula for torque? ›

How Is Torque Calculated? A simple way to calculate the magnitude of the torque is to first determine the lever arm and then multiply it times the applied force. where r is the length of the lever arm and θ is the angle between the force vector and the lever arm.

The equation T=kDP is used to estimate fastener torque calculations, where: T = Torque in newton-meters (Nm) k = Coefficient of friction. D = Diameter of the fastener in millimeters (mm)

A pound-foot (lbf·ft) is a unit of torque or moment of force (a pseudovector). One pound-foot is the torque created by one pound force acting at a perpendicular distance of one foot from a pivot point. Torque is derived from the SI units of Length, Mass, and Time.

A pound-foot (lb⋅ft), abbreviated from pound-force foot (lbf · ft), is a unit of torque representing one pound of force acting at a perpendicular distance of one foot from a pivot point. Conversely one foot pound-force (ft · lbf) is the moment about an axis that applies one pound-force at a radius of one foot.

The SI unit for torque is the Newton-metre or kgm²sec-². How have we come to this? If we look at the formula Torque = Force X Distance. While distance is measured in metres and force is measured in newton, so torque is measured in newton ⋅ metres.

The following formula is used to calculate the Torque From Power. To calculate torque from power, multiply the power by 60, then divide by the result of 2 times pi times the RPM.

Steps for Calculating Torque

Step 2: Substitute these quantities into the equation τ = | r | | F | sin ⁡ to calculate the torque. Step 3: Apply the right hand rule to determine the direction of the torque.